VE

Rear Roof Spoiler for VE / VF Holden Commodore Wagon   If you're looking for a Rear Roof Spoiler for VE / VF Holden Commodore Wagon then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Rear Roof Spoiler for VE / VF Holden Commodore Wagon (2007 - 2017 Models) Give the roof of your Commodore Wagon a whole new look with this TOUGH looking roof spoiler! Fits VE / VF Series Holden Commodore Wagons; Evoke / SS / SS Black / SSV / Redline / SV6 / Z Series / Omega / Equipe Made of high quality ABS plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass spoiler (But you can paint it if you want it to match your cars colour) Easy installation - Meant to be glued in place using urethane/sikaflex or similar Fits over the small factory rear roof spoiler - Does not affect the reversing camera or sensor Note that this spoiler as standard has an approx 8-12mm gap on each side Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!   How to Fit: This spoiler is meant to be glued down with urethane (can be found at Supercheap Auto etc) Clean both surfaces with a wax & grease remover (spoiler and your car) really well so it is perfectly clean. Not prepping it correctly will not allow the urethane to contact properly Apply the urethane on both surfaces and tape it down tight with tape and also put some light-ish weight on it Leave overnight (as long as you can is best though)  

Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 2 - Sports Wing Style   If you're looking for a Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 2 in Sports Wing Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 2 - Sports Wing Style Give the rear end of your Commodore a whole new look with this TOUGH looking boot spoiler! Fits VE Commodore 2010 - 2013 (Series 2 ONLY) - SS / SS V / SV6 / V / Lumina / Omega / International / Calais / Berlina - HSV E3 (2010-2013) - Clubsports R8 / GXP / GTS / Senator (Does NOT fit Series 1 models - See other listing for series 1) Made of high quality ABS plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass spoiler (But you can paint it if you want it to match your cars colour) Can keep your badge installed as spoiler does not come down far enough to touch it Super easy installation - Has inserts in spoiler to attach to boot Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!

Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 1 - Sports Wing Style   If you're looking for a Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 1 in Sports Wing Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Rear Boot Lip Spoiler for VE Holden Commodore Sedan Series 1 - Sports Wing Style Give the rear end of your Commodore a whole new look with this TOUGH looking boot spoiler! Fits VE Commodore Series 1 ONLY - SS / SS V / SV6 / V / Lumina / Omega / International / Calais / Berlina - HSV E3 (2010-2013) - Clubsports R8 / GXP / GTS / Senator (Does NOT fit Series 2 models - See other listing for Series 2) Made of high quality ABS plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass spoiler (But you can paint it if you want it to match your cars colour) Can keep your badge installed as spoiler does not come down far enough to touch it Super easy installation - Has inserts in spoiler to attach to boot Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!

Rear Boot Lip Spoiler for VE Holden Commodore Sedan - R Type (2006 - 2013 Models) If you're looking for a Rear Boot Lip Spoiler for VE Holden Commodore Sedan then this is the one for you. Tough look, plus tough construction. Give your car that sleek aftermarket look and make it stand out from the crowd!   Rear Boot Lip Spoiler for VE Holden Commodore Sedan - R Type (2006 - 2013 Models) Add that extra touch to your car with this sleek boot lip spoiler Made of tough polyurethane - Because of the pliable, flexible material, this spoiler can be curved to fit your car easily Matt black in colour (Unpainted non-glossy finish) Has 3M double sided tape on back of spoiler - See Important Note Below PLEASE NOTE: This spoiler may come in a tube or rolled up in a package (Depends on your location). Because of the flexible material of this spoiler, this does NOT affect its final shape. Heating this spoiler up in the sun or with a heat gun or similar will allow this spoiler to mould to many different shapes.  Please allow 1-3 days for handling BEFORE this item is shipped out to you Tough look plus increases your cars value Limited Stock - Add to Cart Now!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world! Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. Be sure to sit this spoiler on your car BEFORE trying to stick it to your car. DO NOT panic when you receive this spoiler thinking it is not the exact shape of your car. These spoilers are made to mould to all different shapes. So you must heat this item up out in the sun, with a heat gun or hair dryer which will make it nicely pliable to mould to the shape of your car. The double sided tape (provided on back of spoiler) and using some sikaflex/urethane (not supplied), can be used to stick the spoiler down. We also recommend screwing it down. When fitting, apply firm but not excessive pressure or weight. If you are in any way unsure of how to attach this to your vehicle, please get a professional to attach it. We will not be held liable for any fitment issues for how you or anyone else fits this spoiler or the item becoming unattached from your vehicle. Failing to follow these instructions will void any return or refund policy on the product.

Master Power Window Switch with Green Lighting for VE Holden Commodore Sedan / Wagon   If you're looking for aftermarket parts and accessories for your ride then you've come to the right place. Whether you want to freshen up your ride or your old gear is worn out, this quality part will get the job done. Give your car that aftermarket look and style. Master Power Window Switch with Green Lighting for VE Holden Commodore Sedan / Wagon Brand new aftermarket replacement part Direct Replacement Ready to install - Professional installation recommended (no fitting instructions included) Super strong build quality Shipping Australia Wide Note: Please see table below for details & all models this item fits   Make Model Series Year Engine Fuel Body Style Note Holden Commodore VE 2006-2013 All Engine Petrol Sedan Illuminated with Green LED Light Holden Commodore VE 2008-2013 All Engine Petrol SportWagon Illuminated with Green LED Light

Bonnet Scoop for VE Holden Commodore - Reverse Cowl - VK Retro Style   If you're looking for a Bonnet Scoop for VE Holden Commodore in VK Retro Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Bonnet Scoop for VE Holden Commodore - Reverse Cowl - VK Retro Style Toughen up the front end of your VE with this popular 'retro' style reverse cowl bonnet scoop! 100% Australian made Has reverse opening (Reverse cowl) Fits the contour of the VE bonnet perfectly Has threaded studs on underside of scoop to screw bolts into (Does not have inner flange to glue sikaflex / urethane on - It must be bolted to bonnet) Approx 75mm in height at rear opening (Approx only) This product is made to order - Please see above for approx build time Custom designed to suit this model Quality guaranteed Super strong build quality Full fibreglass construction Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

20x Wheel Lug Nuts for VE / VF Holden Commodore - 14mm x 1.5 - Black   Looking for the perfect aftermarket replacement for your ride? For top-notch gear, you’re in the right spot. Whether it’s damaged, outdated, or you’re upgrading, this quality part is just what you need. 20x Wheel Lug Nuts for VE / VF Holden Commodore - 14mm x 1.5 - Black Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Package Contents: 20x Wheel Lug Nuts  

LED Tail Lights for VE Holden Commodore Sedan - Black Altezza Style   If you're looking for a set of LED Tail Lights for VE Holden Commodore Sedan in Black Altezza Style then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style.   LED Tail Lights for VE Holden Commodore Sedan - Black Altezza Style Give your VE rear end a whole new look with these sleek, modern LED tail lights! Suits VE Series 1 & 2 Omega / Lumina / SS / SSV / SV6 sedan 08/2006 - 02/2013 models NOTE: Will NOT fit Berlina & Calais models Top quality plastic aftermarket tail lights Supplied as a pair (Left & Right) Clear outer lens and black inner background Has LED lights for the brake lights  Plug & Play - No wiring modification needed – Plugs straight into factory wiring Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, Specials, New Parts and all the latest in the Automotive World!

Bonnet Scoop for VE Holden Commodore - 4 Inch Reverse Cowl If you're looking for a Bonnet Scoop for VE Holden Commodore then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Bonnet Scoop for VE Holden Commodore - 4 Inch Reverse Cowl Give your Commodore a whole new look with this tough looking bonnet scoop! 100% Australian made Meant to be attached to bonnet with urethane and small screws Will not fit Caprice models (Some modifications may make it fit though) This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Front Right Inner Door Handle for VE Holden Commodore / Statesman / Caprice WM   Looking for the perfect aftermarket replacement for your ride? For top-notch gear, you’re in the right spot. Whether it’s damaged, outdated, or you’re upgrading, this quality part is just what you need. Front Right Inner Door Handle for VE Holden Commodore / Statesman / Caprice WM Metal & Plastic construction Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Compatible with part number(s): 80008367 Package Contents: 1x Right Front Inner Door Handle  

Rear Boot Lip Spoiler for VE Holden Commodore Sedan - Carbon Fibre Look If you're looking for a Rear Boot Lip Spoiler for VE Holden Commodore Sedan in a Carbon Fibre Look then this is the one for you. Tough look, plus tough construction. Give your car that sleek aftermarket look and make it stand out from the crowd! Rear Boot Lip Spoiler for VE Holden Commodore Sedan - Carbon Fibre Look Add that extra touch to your car with this sleek boot lip spoiler Made of tough polyurethane - Because of the pliable, flexible material, this spoiler can be curved to fit your car easily Carbon Fibre look finish (This spoiler is NOT made of carbon fibre) Has 3M double sided tape on back of spoiler - See Important Note Below PLEASE NOTE: This spoiler may come in a tube or rolled up in a package (Depends on your location). Because of the flexible material of this spoiler, this does NOT affect its final shape. Heating this spoiler up in the sun or with a heat gun or similar will allow this spoiler to mould to many different shapes.  Please allow 1-3 days for handling BEFORE this item is shipped out to you Tough look plus increases your cars value Limited Stock - Add to Cart Now! Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world! Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. Be sure to sit this spoiler on your car BEFORE trying to stick it to your car. DO NOT panic when you receive this spoiler thinking it is not the exact shape of your car. These spoilers are made to mould to all different shapes. So you must heat this item up out in the sun, with a heat gun or hair dryer which will make it nicely pliable to mould to the shape of your car. The double sided tape (provided on back of spoiler) and using some sikaflex/urethane (not supplied), can be used to stick the spoiler down. We also recommend screwing it down. When fitting, apply firm but not excessive pressure or weight. If you are in any way unsure of how to attach this to your vehicle, please get a professional to attach it. We will not be held liable for any fitment issues for how you or anyone else fits this spoiler or the item becoming unattached from your vehicle. Failing to follow these instructions will void any return or refund policy on the product.

Twin Vent Bonnet Scoop - Universal Design to Fit Most Bonnets If you're looking for a Twin Vent Bonnet Scoop to Fit Most Bonnets then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Twin Vent Bonnet Scoop - Universal Design to Fit Most Bonnets Give your car's front end a whole new look with this TOUGH looking bonnet scoop! 100% Australian made Can be made to fit pretty much any model bonnet with some modification - Can use Sikaflex/Urethane to fill any small gaps (We've had customers fit these on Hilux's, VS Commodores and many more) Length: 70cm, Width: 67cm, Vent width: 55cm, Height: Approx 6cm Meant to be attached with urethane & small screws  This product is made to order - Please see above for approx build time Full fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Cold Air Intake Kit to suit VE V6 3.6L Alloytec Engine 5/2006 - 2009   >>> The VE Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake Kit to suit VE V6 3.6L Alloytec Engine 5/2006 - 2009 then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. GenAiration 4 Alloytec V6 Series intake for Holden VE V6 SSV / Calais / Omega with 3.6L Alloytec engine Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit ***   Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Top Strut Mounts with Bearing x 2 for VR / VS / VT / VX / VU / VY / VZ / VE / VF Holden Commodore   If you're looking for an aftermarket replacement part for your vehicle then you've come to the right place. Whether your old gear is broken, worn out or you just want to freshen up your ride, this quality part will get the job done. Top Strut Mounts with Bearing x 2 for VR / VS / VT / VX / VU / VY / VZ / VE / VF Holden Commodore Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Note: Please see below for details & all models this item fits Compatibility with other Models: Holden Adventra VY 2003-2005: CX8, LX8, AWD, 4-door Wagon, Front VZ 2005-2009: CX6, LX6, LX8, SX6, AWD, 4-door Wagon, Front Berlina VE 2006-2010: International, RWD, 4-door Sedan, Front VE 2008-2010: International, RWD, 5-door Wagon, Front VX 2000-2002: RWD, 4-door Sedan, Front VX 2000-2002: RWD, 4-door Wagon, Front VY 2002-2004: RWD, 4-door Sedan, Front VY 2002-2004: International, RWD, 4-door Wagon, Front VZ 2004-2006: RWD, 4-door Sedan, Front VZ 2004-2007: RWD, 4-door Wagon, Front Calais VE 2006-2010: V, V 60th Anniversary, V International, V Redline, RWD, 4-door Sedan, Front VE 2008-2010: V, V Redline, RWD, 4-door Wagon, Front VR 1995: RWD, 4-door Sedan, Front VS 1995-1997: RWD, 4-door Sedan, Front VT 1997-2000: 50th Anniversary, International, RWD, 4-door Sedan, Front VX 2000-2002: International, RWD, 4-door Sedan, Front VY 2002-2004: RWD, 4-door Sedan, Front VZ 2004-2006: RWD, 4-door Sedan, Front Commodore VE 2007-2012: Various models, RWD, 2-door Utility, Front VE 2006-2012: Various models, RWD, 4-door Sedan, Front VE 2006-2007, 2011-2012: RWD, 4-door Wagon, Front VE 2008-2010: Various models, RWD, 5-door Wagon, Front VE 2011-2012: Various models, RWD, Sedan, Front VF 2013-2014: Various models, RWD, 2-door Utility, Front VF 2013-2014: Various models, RWD, 4-door Sedan, Front VF 2013-2014: Various models, RWD, 4-door Wagon, Front Crewman VY 2003-2004: Cross 8, AWD, 4-door Utility Dual Cab, Front VY 2003-2004: S, SS, RWD, 4-door Utility Dual Cab, Front VZ 2004-2006: Cross 6, Cross 8, AWD, 4-door Utility Dual Cab, Front VZ 2004-2007: Cross 8, S, SS, RWD, 4-door Utility Dual Cab, Front Monaro V2 2001-2004: CV6, CV8, CV8 R, RWD, 2-door Coupe, Front VZ 2004-2005: CV8, CV8 Z, RWD, 2-door Coupe, Front One Tonner VY 2003-2004: S, RWD, 2-door Cab Chassis, Front VZ 2005: Cross 6, AWD, 2-door Cab Chassis, Front VZ 2004-2005: S, RWD, 2-door Cab Chassis, Front Statesman VS 1995-1999: 50th Anniversary, International, RWD, 4-door Sedan, Front WH 1999-2003: International, International LS8, RWD, 4-door Sedan, Front WK 2003-2004: RWD, 4-door Sedan, Front WL 2004-2006: International, RWD, 4-door Sedan, Front Holden (HSV) Performance Models Clubsport VE 2006-2010: GXP, R8, R8 20th Anniversary, RWD, 4-door Sedan, Front VE 2008-2010: R8 Tourer, RWD, 4-door Wagon, Front VS 1995-1997: RWD, 4-door Sedan, Front VS 1995-1997: RWD, 4-door Wagon, Front VT 1997-2000: 10th Anniversary, Grant Hackett, R8, R8 Grant Hackett, RWD, 4-door Sedan, Front VX 2000-2002: 15th Anniversary, R8, R8 15th Anniversary, RWD, 4-door Sedan, Front Coupe VZ 2004-2005: 4, 4X4 Constant, 2-door Coupe, Front VZ 2004-2006: GTO, GTO LE, GTO Signature, RWD, 2-door Coupe, Front Grange VS 1996-1999: 185i, 195i, 215i, RWD, 4-door Sedan, Front WH 1999-2003: RWD, 4-door Sedan, Front WK 2003-2004: RWD, 4-door Sedan, Front WL 2004-2006: RWD, 4-door Sedan, Front GTO VX 2003-2007: RWD, 2-door Coupe, Front VZ 2003-2007: RWD, 2-door Coupe, Front GTS VE 2006-2010: 40th Anniversary, RWD, 4-door Sedan, Front VS 1996: RWD, 4-door Sedan, Front VT 1998-2000: RWD, 4-door Sedan, Front VX 2000-2001: RWD, 4-door Sedan, Front Maloo VE 2007-2010: GXP, R8, R8 20th Anniversary, RWD, 2-door Utility, Front VS 1995-2000: 10th Anniversary, 185i, 195i, RWD, 2-door Utility, Front VU 2001-2002: 15th Anniversary, R8, RWD, 2-door Utility, Front Manta VS 1995-1997: 185i, RWD, 4-door Sedan, Front VS 1995: 185i, RWD, 4-door Wagon, Front VT 1998-1999: 195i, RWD, 4-door Sedan, Front Senator VE 2006-2010: Signature, Signature SV08, RWD, 4-door Sedan, Front VS 1995-1997: 185i, 215i, RWD, 4-door Sedan, Front VT 1997-2000: Signature, Signature 10th Anniversary, Signature 195i, Signature 220i, RWD, 4-door Sedan, Front VT 1997-1999: Signature, Signature 195i, Signature 220i, RWD, 4-door Wagon, Front VX 2000-2002: 300, Signature, RWD, 4-door Sedan, Front VX 2001: SV300, RWD, 4-door Sedan, Front W427 VE 2008-2009: RWD, 4-door Sedan, Front XU6 VT 1998: 10th Anniversary, RWD, 4-door Sedan, Front VX 2001: RWD, 4-door Sedan, Front XU8 VT 1999: 195i, RWD, 4-door Sedan, Front Toyota Lexcen VR 1993-1995: CSi, Newport, VXi, RWD, 4-door Sedan, Front VR 1993-1995: CSi, VXi, RWD, 4-door Wagon, Front VS 1995-1997: CSi T4, CSi T5, Newport T4, Newport T5, VXi T4, VXi T5, RWD, 4-door Sedan, Front VS 1995-1997: CSi T4, CSi T5, VXi T4, VXi T5, RWD, 4-door Wagon, Front Package Contents: 2x Strut Mounts & Bearings  

Bonnet Vents for Falcons / Commodores / 4x4's - Universal Design If you're looking for Bonnet Vents for Ford Falcons / Holden Commodores / 4x4's in a Universal Design then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Bonnet Vents for Falcons / Commodores / 4x4's - Universal Design Give your vehicles bonnet a new look with these super sleek bonnet vents! Fits basically on any bonnet on any vehicle: Commodores, Falcons, Landcruisers, Patrols, Hilux's, Navara's, Prado's, Ranger's, Amarok's & more Choose between GLOSS finish or MATT finish Made of high quality plastic No need to paint - Can be installed as is - Save time & money over preparing & painting fibreglass vents (But you can paint them if you want it to match your cars colour) Super easy installation - Has 3M tape on the back to apply to your bonnet These are decorative vents - No holes in these vents so as to avoid water trapment (although you can cut them yourself if you want to use them as functional vent) Approx measurements: 420mm long x 80mm wide Please allow 2-3 days for handling BEFORE this item is shipped to you High quality great-looking durable finish Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!   Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. When fitting, apply firm but not excessive pressure or weight. Failing to follow these instructions will void your warranty on the product.

Cold Air Intake Kit to suit VE V6 3.6L SIDI Engine 5/2009-9/2011   >>> The VE Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake Kit to suit VE V6 3.6L SIDI Engine 5/2009-9/2011 then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Orssom Performance MY10 – MY11 VE V6 3.6L Sidi Over The Radiator Cold Air Intake   SUITS: VE V6 3.6L Holden Commodores MY10 & MY11 Series ( 5 / 2009 to 8 / 2011 ) fitted with the 3.6L Sidi engine. Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit *** Important! Please take the time to read Important Information why we recommend a tune be carried out when installing this particular product.   Engine Management Light:The engine management light on your dash is also known as the EML. This light comes on when one or more of your sensors are not functioning properly Or the Maps that are set in your factory computer have gone over there set parameters (Please refer to the diagram below). Fuel Trims:Monitored by the Oxygen sensors, Fuel trims are used to (+) add or (-) subtract fuel from the engine. Why were fuel trims created? In order for vehicle manufacturers to comply with EPA emissions regulations. Oxygen Sensors:The purpose for Oxygen sensors which are fitted in the Exhaust systems is to sample the Air Fuel mixture & along with many other sensors located on your motor relay messages back to the factory computer on what’s happening at various points in the engine. The Air Flow Meter:In your VE Commodore the Air Flow Meter, Also known as a Maf sensor, is used to calculate the amount of air flowing thru the sensor & into your engine. The engines uses rpm in conjunction with the (MAF) to calculate engine load. Factory Computer:The factory computer has basic maps & parameters Tuned / Programmed in by the Manufacturer. Apart from the basics, the purpose of the computer is to carry out necessary adjustments to: Fuel / Spark / Timing maps depending on the information it receives from these sensors The EML light coming on is not a common problem, but can arise on some vehicle from time to time which are more sensitive than others.In your case, (as shown in the graph below) the fuel trim maps have gone over the factory set ( + / – ) 15% parameter limit & triggered the engine light on the dash now to come on. The factory sensors mentioned above are all working properly & have recognised the extra air now entering the engine, but the factory computer as yet has not compensated for that extra air. This is not a product fault, Regardless of which Brand / Company Intake product that you install, you may still experience the same outcome with the EML. This EML light coming on is not only pinned down to Cold Air Intakes. On some cars fitting a Sports Exhaust it has been known to trigger the EML light. If you do happen to experience an EML light coming on or have a combination of both Intake & Exhaust fitted to your vehicle and the light hasn’t gone away within the first 500km’s of driving, then we do strongly recommend a custom tune be carried out, as the factory parameters are stretched to there limit. 3 simple things we recommend you do: If your using that rubbish E10 fuel get rid of it. Fill up your next tank with 95 or 98 Octane fuel. Even thou your fuel cap say’s E10 suitable, we do not recommend it for high compression engine. Disconnect your car battery for at least 15 mins. This will reset the factory computer and wipe out the engine light fault on the dash. Drive your car for at least 300 to 500km for the computer can learn the new values. If the EML light doesn’t go off by then a Custom Tune is required. Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

2.5" Eliminator Pipes for VE Holden Commodore 8Cyl SV6 / SS / SSV / Calais / Omega Sedan   Craving more power and a throatier growl? This high-performance exhaust system delivers both and more. Fits dual-exit pipe VE Holden Commodore 8 Cyl SV6 / SS / SSV / Calais / Omega Sedan Note: Will NOT fit onto an aftermarket sports exhaust 2.5" / 63mm Mandrel Bent aluminised steel tubing Comes with flange gaskets Hassle-free fit — unbolt the stock muffler and swap it with this one. Bolt-on system — no welding or car modifications required Order yours today and give your vehicle a whole new vibe!  

2.5" Eliminator Pipes for VE Holden Commodore 8Cyl SV6 / SS / SSV / Calais / Omega Wagon   Looking to unleash your vehicle’s true potential? An Eliminator Pipe enhances exhaust flow, amps up performance, and delivers a bold, head-turning sound. 2.5" Eliminator Pipes for VE Holden Commodore 8 Cyl SV6 / SS / SSV / Calais / Omega Wagon Fits dual-exit pipe VE Holden Commodore 8 Cyl SV6 / SS / SSV / Calais / Omega Wagon Note: Will NOT fit onto an aftermarket sports exhaust 2.5" / 63mm Mandrel Bent aluminised steel tubing Comes with flange gaskets Easy to install — simply unbolt your factory muffler and replace it with this one Bolt-on system — no welding or car modifications required Order yours today and give your vehicle a whole new vibe!      

20x Stainless Steel Capped Wheel Nuts for VE / VF Holden Commodore HSV - M14 x 1.5   Looking for the perfect aftermarket replacement for your ride? For top-notch gear, you’re in the right spot. Whether it’s damaged, outdated, or you’re upgrading, this quality part is just what you need. 20x Stainless Steel Capped Wheel Nuts for VE / VF Holden Commodore HSV - M14 x 1.5 Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Package Contents: 20x Wheel Nuts  

20x Wheel Nuts for VE / VF Holden Commodore - 14mm x 1.5 - Chrome (19mm Socket)   Looking for the perfect aftermarket replacement for your ride? For top-notch gear, you’re in the right spot. Whether it’s damaged, outdated, or you’re upgrading, this quality part is just what you need. 20x Wheel Nuts for VE / VF Holden Commodore - 14mm x 1.5 - Chrome (19mm Socket) Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Package Contents: 20x Wheels Lug Nuts