VF

Roof Spoiler for VE / VF Holden Commodore Ute   If you're looking for 100% Australian made Roof Spoiler for VE / VF Holden Commodore Ute then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Roof Spoiler for VE / VF Holden Commodore Ute  Pimp out your VE ute with this sleek roof spoiler that matches the utes styling perfectly! 100% Australian made Easy installation - To be attached to roof line with sikaflex / urethane - No holes to drill (See basic instructions below) Fits all base models (S pack, SS, Executive etc) - Does NOT fit the HSV models Note that this spoiler has a smooth gel coat finish on top and a raw fibreglass finish on the underneath side This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!   Basic instructions for fitting: Sit the spoiler on the roof where you want it, take note of where it contacts - Then scuff up the plastic sailplane type piece of plastic on the top rear of the cab Also scuff up the spoiler where it contacts the same area. (Scuff it up with sandpaper) You must do this. Scuffing it up gives it something to bond too. If its smooth paint then there is no way it will bond.  Put the urethane / sikaflex on both surfaces and tape it down tight with tape and also put some weight on it.  Leave overnight (as long as you can is best though)    

Rear Window Roof Spoiler for VF Holden Commodore Sedan   If you're looking for a Rear Window Roof Spoiler for VF Holden Commodore Sedan then this is the one for you. Tough look, plus tough construction. Give your car that sleek aftermarket look and make it stand out from the crowd!   Rear Window Roof Spoiler for VF Holden Commodore Sedan Customise your pride and joy with this sleek & stylish roof spoiler! Fits VF Commodore sedan models; Lumina, Evoke, SS, SSV, SV6, Calais Berlina, Omega, Senator etc Dark translucent black in colour - Dark enough for a near black look but can still easily see through it Made of extremely durable & high quality UV resistant acrylic No need to paint Easy installation - Has 3M double sided tape on back of spoiler for easy attachment to car Supplied with spoiler is: 3M brand double sided tape, prep pads, tube of 3M tape primer & basic installation instructions  Please allow 1-3 days for handling BEFORE this item is shipped out to you Super TOUGH look plus increases your cars value Limited Stock - Add to Cart Now!   Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. Be sure to sit this spoiler on your car BEFORE trying to stick it to your car. The double sided tape (provided on back of spoiler) and using some sikaflex/urethane (not supplied), can be used to stick the spoiler down.  When fitting, apply firm but not excessive pressure or weight. If you are in any way unsure of how to attach this to your vehicle, please get a professional to attach it. We will not be held liable for any fitment issues for how you or anyone else fits this spoiler or the item becoming unattached from your vehicle. Failing to follow these instructions will void any return or refund policy on the product.

Weather Shields for VF Holden Commodore Sedan If you're looking for a set of Weather Shields for VF Holden Commodore Sedan then this is the one for you. Very high quality, tough construction and gives your car that aftermarket look and style.    Weather Shields for VF Holden Commodore Sedan Supplied as a set of 4 Fits all Evoke / SS / SS V / SV6 / Motorsport Edition / Redline models High quality translucent black perspex plastic (These are NOT solid black in colour) Darkly tinted black yet extremely easy to see through Highly resistant to cracking and discolouring in the sunlight Ready to fit - Comes with 3M double sided tape on back of weather shields for easy installation Supplied with basic installation instructions Heavy duty UV resistant  Reduces harsh sunlight and wind noise Minimises heat inside car when parked Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Tough look plus increases your cars value Scroll up and Order NOW!

Weather Shields for VE / VF Holden Commodore Ute If you're looking for a set of Weather Shields for VE / VF Holden Commodore Ute then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Weather Shields for VE / VF Holden Commodore Ute Supplied as a set of 2 Fits all VE / VF Holden Commodore Ute models High quality translucent black perspex plastic (These are NOT solid black in colour) Darkly tinted black yet extremely easy to see through Highly resistant to cracking and discolouring in the sunlight Ready to fit - Comes with 3M double sided tape on back of weather shields for easy installation Supplied with basic installation instructions Heavy duty UV resistant  Reduces harsh sunlight and wind noise Minimises heat inside car when parked Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Tough look plus increases your cars value Scroll up and Order NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Bonnet Vents for Holden Commodores If you're looking for 100% Australian made Bonnet Vents for Holden Commodores then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Bonnet Vents for Holden Commodores Give your Commodore bonnet a new look with these great looking vents! 100% Australian made These are decorative vents - No holes in these vents so as to avoid water trapment (although you can cut them yourself if you want to use them as functional vent) Will fit basically all bonnets - Universal capability (VY / VZ / VE / VF etc) Does NOT require moulded bonnet recess Meant to be glued onto bonnet with a strong adhesive This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Comes unpainted - gel coat finish - ready to prep & paint Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Head Light Eyebrows / Eyelids for VF Holden Commodore   If you're looking for a set of Head Light Eyebrows / Eyelids for VF Holden Commodore then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Head Light Eyebrows / Eyelids for VF Holden Commodore Pimp out the front end of your VF simply & easily with these head light eyebrows! Supplied as a set of 2 Fits all Commodore VF 1/2 series Sedan, Ute, Wagon - Evoke / International / SS / SS V / SV6 / Storm / Redline / Black / Calais 2013-2017 / HSV Series- Clubsport / Grange / GTS / Maloo / Senator High quality black injection plastic - NOT just stickers like all the others on the market! Covers all the way to the top of the light, so there is no light 'leak' Low sheen finish - You can paint these to match your cars colour if needed (As these are not a high-gloss finish) Highly resistant to cracking and discolouring in the sunlight Ready to fit - Comes with 3M double sided tape on back for easy installation Heavy duty UV resistant  Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Tough look plus increases your cars value Limited Stock - Scroll up and Order NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Rear Window Roof Spoiler for VE / VF Holden Commodore Sedan   If you're looking for a Rear Window Roof Spoiler for VE / VF Holden Commodore Sedan then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Rear Window Roof Spoiler for VE / VF Holden Commodore Sedan Polish off the rear of your Commodore with this sleek roof wing! 100% Australian made Fits all VE / VF Commodore sedans  Meant to be attached to the rear window / roof panel with urethane (Has recessed edge underneath - spoiler does not fully mount on glass; approx 15-20mm of this recessed edge sits on top of the roof panel) This product is made to order - Please see above for approx build time Custom designed to suit this model Full fibreglass construction Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!

Front Bumper Bar Lip / Splitter for VF Holden Commodore Series 1   If you're looking for a Front Bumper Bar Lip / Splitter for VF Holden Commodore  Series 1 then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Front Bumper Bar Lip / Splitter for VF Holden Commodore Series 1 Give the front end of your Commodore a completely new look with this TOUGH looking front bumper lip! Fits factory style front bumpers ONLY on VF Series 1 VF1 S / SS / SS Storm / SV6 / SSV / Redline / Craig Lowndes / Sandman (Will not fit series 2 models - See other listing for series 2) Made of high quality PP injection plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass lip (But you can paint it if you want it to match your cars colour) Sits approx 5-7mm lower than your standard front bumper bar Easy installation - Beautiful snug fit to the factory front bumper bar Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!

Bonnet for VF Holden Commodore (Road Legal Certified)   If you're looking for a 100% street legal Bonnet for VF Holden Commodore then this is the one for you. Get the cool air in and the hot air out. Tough look, plus tough construction. Give your car that aftermarket look and style.   Bonnet for VF Holden Commodore - Camaro Style (Road Legal Certified) Pump out the front of your VF Commodore with this super TOUGH looking bonnet! Vented to allow your engine to breathe and improve performance Approx 30mm higher than a standard bonnet in the centre & weighs approx 12-14kg Vents are cut out and functional (See underside picture) 100% Street Legal in all States and Territories Supplied with Road Legal Certification letter (Supply us with your VIN Number and Rego number) Proudly made in Australia Supplied with front bonnet catch & mesh for behind vents If your car has washer jets on the bonnet, then you will need to take them off your old bonnet and transfer them over. We provide some tubing for under the bonnet for this (but not the actual jets) This product is made to order - Please see above for approx build time Custom designed to suit this model Full fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Side Skirts for VE / VF Holden Commodore Sedan & Wagon   If you're looking for 100% Australian made Side Skirts for VE / VF Holden Commodore Sedan & Wagon then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style. Side Skirts for VE / VF Holden Commodore Sedan & Wagon Give your Commodore a whole new look with these TOUGH looking side skirts! Fits all VE & VF Commodore Sedan & Wagon models (Will not fit Caprice models) Supplied as a pair (Can also be supplied separately - Contact us for this)  100% Australian made Meant to be attached using urethane and screws Mesh for holes is not supplied This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Front Bumper Bar Lip / Splitter for VF Holden Commodore Series 2   If you're looking for a Front Bumper Bar Lip / Splitter for VF Holden Commodore  Series 2 then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Front Bumper Bar Lip / Splitter for VF Holden Commodore Series 2 Give the front end of your Commodore a completely new look with this TOUGH looking front bumper lip! Fits factory style front bumpers ONLY on 2015-2017 VF Series 2 VF1 S / SS / SS Storm / SV6 / SSV / Redline / Craig Lowndes / Sandman (Will not fit series 1 models - See other listing for series 1) Made of high quality PP injection plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass lip (But you can paint it if you want it to match your cars colour) Sits approx 5mm lower than standard front bumper Easy installation - Snug fit to the factory front bumper bar Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!

Rear Roof Spoiler for VE / VF Holden Commodore Wagon   If you're looking for a Rear Roof Spoiler for VE / VF Holden Commodore Wagon then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Rear Roof Spoiler for VE / VF Holden Commodore Wagon (2007 - 2017 Models) Give the roof of your Commodore Wagon a whole new look with this TOUGH looking roof spoiler! Fits VE / VF Series Holden Commodore Wagons; Evoke / SS / SS Black / SSV / Redline / SV6 / Z Series / Omega / Equipe Made of high quality ABS plastic with a great looking satin black finish  No need to paint - Can be installed as is - Save time & money over preparing a fibreglass spoiler (But you can paint it if you want it to match your cars colour) Easy installation - Meant to be glued in place using urethane/sikaflex or similar Fits over the small factory rear roof spoiler - Does not affect the reversing camera or sensor Note that this spoiler as standard has an approx 8-12mm gap on each side Please allow 2-3 days for handling BEFORE this item is shipped to you High quality durable finish (Surface may have a slight scuff mark from storage) Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!   How to Fit: This spoiler is meant to be glued down with urethane (can be found at Supercheap Auto etc) Clean both surfaces with a wax & grease remover (spoiler and your car) really well so it is perfectly clean. Not prepping it correctly will not allow the urethane to contact properly Apply the urethane on both surfaces and tape it down tight with tape and also put some light-ish weight on it Leave overnight (as long as you can is best though)  

Bonnet for VF Holden Commodore - Vented Sports Style (Road Legal Certified)   If you're looking for a 100% street legal Bonnet for VF Holden Commodore then this is the one for you. Get the cool air in and the hot air out. Tough look, plus tough construction. Give your car that aftermarket look and style.     Bonnet for VF Holden Commodore - Vented Sports Style (Road Legal Certified) Pump out the front of your VF Commodore with this super TOUGH looking bonnet! Vented to allow your engine to breathe and improve performance Approx 30mm higher than a standard bonnet in the centre & weighs approx 12-14kg 100% Street Legal in all States and Territories  Supplied with Road Legal Certification letter (Just supply us with your VIN & Rego number when ordering so certification can be made up for your car) Proudly made in Australia Supplied with front bonnet catch & mesh for behind vents If your car has washer jets on the bonnet, then you will need to take them off your old bonnet and transfer them over. We provide some tubing for under the bonnet for this (but not the actual jets) Uses all the original mounting points This product is made to order - Please see above for approx build time Full fibreglass construction Custom designed to suit this model Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Mud Flaps for VF Holden Commodore / Calais Sedan x 4 (2013 - 2017)   If you're looking for aftermarket parts and accessories for your ride then you've come to the right place. Whether you want to freshen up your ride or your old gear is worn out, this quality part will get the job done. Give your car that aftermarket look and style. Mud Flaps for VF Holden Commodore / Calais Sedan x 4 (2013 - 2017) Brand new aftermarket replacement part Direct Replacement Ready to install - Professional installation recommended (no fitting instructions included) Super strong build quality Shipping Australia Wide Note: Please see table below for details & all models this item fits   Make Model Submodel Series Year Engine Body Style Holden Commodore SS, SS-V VF 2013-2017 All Engine Sedan Holden Calais SS, SS-V VF 2013-2015 All Engine Sedan

Rear Window Roof Lip Spoiler for VF Holden Commodore Sedan If you're looking for a Rear Window Roof Lip Spoiler for VF Holden Commodore Sedan then this is the one for you. Tough look, plus tough construction. Give your car that sleek aftermarket look and make it stand out from the crowd!   Rear Window Roof Lip Spoiler for VF Holden Commodore Sedan Add that extra touch to your car with this sleek roof lip spoiler Made of tough polyurethane - Because of the pliable, flexible material, this spoiler can be curved to fit your car easily Matt black in colour (Unpainted non-glossy finish) Has 3M double sided tape on back of spoiler - See Important Note Below PLEASE NOTE: This spoiler may come in a tube or rolled up in a package (Depends on your location). Because of the flexible material of this spoiler, this does NOT affect its final shape. Heating this spoiler up in the sun or with a heat gun or similar will allow this spoiler to mould to many different shapes.  Please allow 1-3 days for handling BEFORE this item is shipped out to you Tough look plus increases your cars value Limited Stock - Add to Cart Now!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world! Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. Be sure to sit this spoiler on your car BEFORE trying to stick it to your car. DO NOT panic when you receive this spoiler thinking it is not the exact shape of your car. These spoilers are made to mould to all different shapes. So you must heat this item up out in the sun, with a heat gun or hair dryer which will make it nicely pliable to mould to the shape of your car. The double sided tape (provided on back of spoiler) and using some sikaflex/urethane (not supplied), can be used to stick the spoiler down.  When fitting, apply firm but not excessive pressure or weight. If you are in any way unsure of how to attach this to your vehicle, please get a professional to attach it. We will not be held liable for any fitment issues for how you or anyone else fits this spoiler or the item becoming unattached from your vehicle. Failing to follow these instructions will void any return or refund policy on the product.

Front Stabiliser Sway Bar Links x 2 for VE / VF Holden Commodore Sedan / Wagon / Ute (2006 - 2017)   If you're looking for an aftermarket replacement part for your vehicle then you've come to the right place. Whether your old gear is broken, worn out or you just want to freshen up your ride, this quality part will get the job done. Front Stabiliser Sway Bar Links x 2 for VE / VF Holden Commodore Sedan / Wagon / Ute (2006 - 2017) Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Note: Please see below for details & all models this item fits Compatibility with other Models: Holden Berlina VE 2006-2013 incl. International RWD 4door Sedan Holden Berlina VE 2008-2010 incl. International RWD 5door Wagon Holden Calais VE 2006-2013 incl. V, V 60th Anniversary, V International, V Redline RWD 4door Sedan Holden Calais VE 2008-2013 incl. V, V Redline RWD 4door Wagon Holden Calais VF 2013-2017 RWD 4door Sedan Holden Calais VF 2013-2017 RWD 4door Wagon Holden Commodore VE 2007-2012 incl. i V6, i V6 Dual Fuel LPG, i V8, Omega, SS, SS V, SS V Redline, SS V Special Edition, SV6, SV6 60th Anniversary RWD 2door Utility Holden Commodore VE 2006-2013 incl. 60th Anniversary, i V6, i V6 Dual Fuel LPG, i V8, International, Lumina, Omega, SS, SS V, SS V 60th Anniversary, SS V Redline, SS V Special Edition, SV6, V RWD 4door Sedan Holden Commodore VE 2008-2012 incl. SS, SS-V Redline, SS-V Special Edition, SS-V Sportswagon RWD 4door Wagon Holden Commodore VE 2008-2010 incl. 60th Anniversary, International, Omega, SV6 RWD 5door Wagon Holden Commodore VE 2011 incl. i V8 RWD Sedan Holden Commodore VF 2013-2017 incl. Evoke, SS, SS-V, SV6 RWD 2door Utility Holden Commodore VF 2013-2017 incl. Evoke, SS, SS-V, SV6 RWD 4door Sedan Holden Commodore VF 2013-2017 incl. Sportwagon, SS, SS-V, SV6 Sportwagon RWD 4door Wagon Package Contents: 1x LH + RH Sway Bar (Stabilizer Bar) Link Joint Assembly   

Bonnet Vents for Falcons / Commodores / 4x4's - Universal Design If you're looking for Bonnet Vents for Ford Falcons / Holden Commodores / 4x4's in a Universal Design then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style!   Bonnet Vents for Falcons / Commodores / 4x4's - Universal Design Give your vehicles bonnet a new look with these super sleek bonnet vents! Fits basically on any bonnet on any vehicle: Commodores, Falcons, Landcruisers, Patrols, Hilux's, Navara's, Prado's, Ranger's, Amarok's & more Choose between GLOSS finish or MATT finish Made of high quality plastic No need to paint - Can be installed as is - Save time & money over preparing & painting fibreglass vents (But you can paint them if you want it to match your cars colour) Super easy installation - Has 3M tape on the back to apply to your bonnet These are decorative vents - No holes in these vents so as to avoid water trapment (although you can cut them yourself if you want to use them as functional vent) Approx measurements: 420mm long x 80mm wide Please allow 2-3 days for handling BEFORE this item is shipped to you High quality great-looking durable finish Custom designed to suit this model Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the automotive world!   Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. When fitting, apply firm but not excessive pressure or weight. Failing to follow these instructions will void your warranty on the product.

Rear Boot Spoiler for VF Holden Commodore Sedan   If you're looking for an Australian made Rear Boot Spoiler for VF Holden Commodore Sedan then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.  Rear Boot Spoiler for VF Holden Commodore Sedan Polish off the look of your boot with this sleek bobtail lip spoiler! Australian made Spoiler will fit over the top of the standard factory lip spoiler if needed Has threaded inserts in each leg of spoiler for attachment to boot - Mounts on far edges of each side of the boot Supplied with fittings No LED brake light in spoiler This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!  

Rear Boot Wing Spoiler for VE Holden Commodore Sedan - V8 Supercar Style   If you're looking for 100% Australian made Rear Boot Wing Spoiler for VE Holden Commodore Sedan in V8 Supercar Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Rear Boot Wing Spoiler for VE Holden Commodore Sedan - V8 Supercar Style Give your VE the V8 Supercar look with this large boot wing! Fully adjustable - Angle of wing can be adjusted up & down 100% Australian made Can also fit the VF (as shown in main images), but the base will need shaving down on the underside of the legs to suit the curve of the VF boot (NOTE: This is something you would need to do yourself) This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Harmonic Balancer for VE / VF Holden Commodore HSV / Statesman WM / WN LS2 / LS3 / L76 / L77 / L98   If you're looking for an aftermarket replacement part for your vehicle then you've come to the right place. Whether your old gear is broken, worn out or you just want to freshen up your ride, this quality part will get the job done. Harmonic Balancer for VE / VF Holden Commodore HSV / Statesman WM / WN LS2 / LS3 / L76 / L77 / L98 Brand new aftermarket replacement part Ready to install Super strong build quality Shipping Australia Wide Note: Please see below for details & all models this item fits Compatibility with other Models: Chevrolet   Camaro 2009 - , 6.2L, V8, 16V, OHV, MPFI, 321kW, EngCode: LS3   2010 - , 6.2L, V8, 16V, OHV, MPFI, 302kW, EngCode: L99 Corvette 1997 - 2004, 5.7L, V8, 16V, OHV, MPFI, C5, EngCode: LS1   2007 - 2004, 6.0L, V8, 16V, OHV, MPFI, C6, EngCode: LS2   2014 - , 6.2L, V8, 16V, OHV, MPFI, C7, 339kW, EngCode: LT1 Lumina Aug 2006 - Aug 2010, 6.0L, V8, 16V, OHV, MPFI, VE, EngCode: L98 GEN 4 Holden   Berlina Aug 2006 - Jan 2010, 6.0L, V8, 16V, OHV, MPFI, VE, 270kW, EngCode: L98 Calais Aug 2006 - Oct 2008, 6.0L, V8, 16V, OHV, MPFI, VE, 270kW, EngCode: L98   Nov 2008 - Aug 2010, 6.0L, V8, 16V, OHV, MPFI, VE, 260kW, EngCode: L76   Sep 2010 - Apr 2013, 6.0L, V8, 16V, OHV, MPFI, VE II, 260kW, EngCode: L77   May 2013 - Sep 2015, 6.0L, V8, 16V, OHV, MPFI, VF, 260kW, EngCode: L77   Oct 2015 - Oct 2017, 6.2L, V8, 16V, OHV, MPFI, VF, 304kW, EngCode: LS3 Caprice Aug 2006 - Oct 2008, 6.0L, V8, 16V, OHV, MPFI, WM , 270kW, EngCode: L98   Nov 2008 - Aug 2010, 6.0L, V8, 16V, OHV, MPFI, WM , 270kW, EngCode: L76   Sep 2010 - Apr 2013, 6.0L, V8, 16V, OHV, MPFI, WM II, 260kW, EngCode: L77   May 2013 - , 6.0L, V8, 16V, OHV, MPFI, WN, 270kW, EngCode: L77 Commodore Aug 2006 - Aug 2010, 6.0L, V8, 16V, OHV, MPFI, VE, 270kW, EngCode: L98 GEN 4   Sep 2010 - Apr 2013, 6.0L, V8, 16V, OHV, VE, 270kW, EngCode: L77   May 2013 - Sep 2015, 6.0L, V8, 16V, OHV, MPFI, VF, 270kW, EngCode: L77   Oct 2015 - Oct 2017, 6.2L, V8, 16V, OHV, MPFI, VF, 304kW, EngCode: LS3 Statesman  Aug 2006 - Aug 2010, 6.0L, V8, 16V, OHV, MPFI, WM , 270kW, EngCode: L98 HSV   Clubsport Aug 2006 - Mar 2008, 6.0L, V8, 16V, OHV, MPFI, VE, EngCode: LS2   Apr 2008 - May 2013, 6.2L, V8, 16V, OHV, MPFI, VE, 317kW, EngCode: LS3   Sep 2010 - May 2013, 6.2L, V8, 16V, OHV, MPFI, VE LPG, 317kW, EngCode: LS3   Jun 2013 - Oct 2017, 6.2L, V8, 16V, OHV, MPFI, VF, 317kW, EngCode: LS3   Jun 2013 - Oct 2015, 6.2L, V8, 16V, OHV, MPFI, VF, R8, 325kW, EngCode: LS3   Oct 2014 - Oct 2017, 6.2L, V8, 16V, OHV, MPFI, VF, 325kW, EngCode: LS3   Oct 2016 - Oct 2017, 6.2L, V8, 16V, OHV, MPFI, VF, R8, 340kW, EngCode: LS3 Grange Mar 2007 - Mar 2008, 6.0L, V8, 16V, OHV, MPFI, WM , EngCode: LS2   Apr 2008 - May 2013, 6.2L, V8, 16V, OHV, MPFI, WM , 325kW, EngCode: LS3   Jun 2013 - Feb 2017, 6.2L, V8, 16V, OHV, MPFI, WN, 325kW, EngCode: LS3 GTS Aug 2006 - Mar 2008, 6.0L, V8, 16V, OHV, MPFI, VE, 307kW, EngCode: LS2   Apr 2008 - Aug 2009, 6.2L, V8, 16V, OHV, MPFI, VE, 317KW, EngCode: LS3   Sep 2009 - May 2013, 6.2L, V8, 16V, OHV, MPFI, VE, 325KW, EngCode: LS3   Sep 2010 - May 2013, 6.2L, V8, 16V, OHV, MPFI LPG, VE, 325KW, EngCode: LS3 Maloo Oct 2007 - Mar 2008, 6.0L, V8, 16V, OHV, MPFI, VE, 307kW, EngCode: LS2   Apr 2008 - May 2013, 6.2L, V8, 16V, OHV, MPFI, VE, 317kW, EngCode: LS3   Sep 2010 - May 2013, 6.2L, V8, 16V, OHV, MPFI LPG, VE, 317kW, EngCode: LS3   Jun 2013 - Oct 2015, 6.2L, V8, 16V, OHV, MPFI LPG, VF R8, 325kW, EngCode: LS3 Senator Aug 2007 - Mar 2008, 6.0L, V8, 16V, OHV, MPFI, VE, 307kW, EngCode: LS2   Apr 2008 - May 2013, 6.2L, V8, 16V, OHV, MPFI, VE, 317kW, EngCode: LS3   Package Contents: 1x Harmonic Balancer

Bonnet Bulge for VF Holden Commodore If you're after an Australian made Bonnet Bulge for VF Holden Commodore, this is the perfect choice. Designed with a tough, durable construction, it not only enhances protection but also gives your car a bold aftermarket look and style. Bonnet Bulge for VF Holden Commodore Give your Commodore a whole new look with this TOUGH looking bonnet bulge 100% Australian made Meant to be attached with urethane & small screws (underside has a flange to drill and screw into) This product is made to order - Please see above for approx build time Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart Now