Holden

Cold Air Intake Kit to suit VF V6 3.6L SIDI Engine   >>> The VF Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake Kit to suit VF V6 3.6L SIDI Engine then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Orssom Performance VF V6 3.6L Sidi Over The Radiator Cold Air Intake. SUITS: VF V6 3.6L Holden Commodores fitted with the 3.6L Sidi engine. Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit *** Important! Please take the time to read Important Information why we recommend a tune be carried out when installing this particular product.   Engine Management Light:The engine management light on your dash is also known as the EML. This light comes on when one or more of your sensors are not functioning properly Or the Maps that are set in your factory computer have gone over there set parameters (Please refer to the diagram below). Fuel Trims:Monitored by the Oxygen sensors, Fuel trims are used to (+) add or (-) subtract fuel from the engine. Why were fuel trims created? In order for vehicle manufacturers to comply with EPA emissions regulations. Oxygen Sensors:The purpose for Oxygen sensors which are fitted in the Exhaust systems is to sample the Air Fuel mixture & along with many other sensors located on your motor relay messages back to the factory computer on what’s happening at various points in the engine. The Air Flow Meter:In your VE Commodore the Air Flow Meter, Also known as a Maf sensor, is used to calculate the amount of air flowing thru the sensor & into your engine. The engines uses rpm in conjunction with the (MAF) to calculate engine load. Factory Computer:The factory computer has basic maps & parameters Tuned / Programmed in by the Manufacturer. Apart from the basics, the purpose of the computer is to carry out necessary adjustments to: Fuel / Spark / Timing maps depending on the information it receives from these sensors The EML light coming on is not a common problem, but can arise on some vehicle from time to time which are more sensitive than others.In your case, (as shown in the graph below) the fuel trim maps have gone over the factory set ( + / – ) 15% parameter limit & triggered the engine light on the dash now to come on. The factory sensors mentioned above are all working properly & have recognised the extra air now entering the engine, but the factory computer as yet has not compensated for that extra air. This is not a product fault, Regardless of which Brand / Company Intake product that you install, you may still experience the same outcome with the EML. This EML light coming on is not only pinned down to Cold Air Intakes. On some cars fitting a Sports Exhaust it has been known to trigger the EML light. If you do happen to experience an EML light coming on or have a combination of both Intake & Exhaust fitted to your vehicle and the light hasn’t gone away within the first 500km’s of driving, then we do strongly recommend a custom tune be carried out, as the factory parameters are stretched to there limit. 3 simple things we recommend you do: If your using that rubbish E10 fuel get rid of it. Fill up your next tank with 95 or 98 Octane fuel. Even thou your fuel cap say’s E10 suitable, we do not recommend it for high compression engine. Disconnect your car battery for at least 15 mins. This will reset the factory computer and wipe out the engine light fault on the dash. Drive your car for at least 300 to 500km for the computer can learn the new values. If the EML light doesn’t go off by then a Custom Tune is required. Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Cold Air Intake MAF Kit to suit VE V8 6.0 & 6.2L Engines - 2007-2013   >>> The VE Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake MAF Kit to suit VE V8 6.0 & 6.2L Engines - 2007-2013 then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Suits all Holden VE SS and SSV V8 Commodores including the Holden HSV variants fitted with the 6.0 and 6.2 litre LS2 and LS3 engines, L76 – L77 – L98.   Also suits the following overseas models: Chevrolet Lumina  (U.A.E) Pontiac G8              (USA) Vauxhall VXR8       (UK) Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit *** Important! Please take the time to read Important Information why we recommend a tune be carried out when installing this particular product.   Engine Management Light:The engine management light on your dash is also known as the EML. This light comes on when one or more of your sensors are not functioning properly Or the Maps that are set in your factory computer have gone over there set parameters (Please refer to the diagram below). Fuel Trims:Monitored by the Oxygen sensors, Fuel trims are used to (+) add or (-) subtract fuel from the engine. Why were fuel trims created? In order for vehicle manufacturers to comply with EPA emissions regulations. Oxygen Sensors:The purpose for Oxygen sensors which are fitted in the Exhaust systems is to sample the Air Fuel mixture & along with many other sensors located on your motor relay messages back to the factory computer on what’s happening at various points in the engine. The Air Flow Meter:In your VE Commodore the Air Flow Meter, Also known as a Maf sensor, is used to calculate the amount of air flowing thru the sensor & into your engine. The engines uses rpm in conjunction with the (MAF) to calculate engine load. Factory Computer:The factory computer has basic maps & parameters Tuned / Programmed in by the Manufacturer. Apart from the basics, the purpose of the computer is to carry out necessary adjustments to: Fuel / Spark / Timing maps depending on the information it receives from these sensors The EML light coming on is not a common problem, but can arise on some vehicle from time to time which are more sensitive than others.In your case, (as shown in the graph below) the fuel trim maps have gone over the factory set ( + / – ) 15% parameter limit & triggered the engine light on the dash now to come on. The factory sensors mentioned above are all working properly & have recognised the extra air now entering the engine, but the factory computer as yet has not compensated for that extra air. This is not a product fault, Regardless of which Brand / Company Intake product that you install, you may still experience the same outcome with the EML. This EML light coming on is not only pinned down to Cold Air Intakes. On some cars fitting a Sports Exhaust it has been known to trigger the EML light. If you do happen to experience an EML light coming on or have a combination of both Intake & Exhaust fitted to your vehicle and the light hasn’t gone away within the first 500km’s of driving, then we do strongly recommend a custom tune be carried out, as the factory parameters are stretched to there limit. 3 simple things we recommend you do: If your using that rubbish E10 fuel get rid of it. Fill up your next tank with 95 or 98 Octane fuel. Even thou your fuel cap say’s E10 suitable, we do not recommend it for high compression engine. Disconnect your car battery for at least 15 mins. This will reset the factory computer and wipe out the engine light fault on the dash. Drive your car for at least 300 to 500km for the computer can learn the new values. If the EML light doesn’t go off by then a Custom Tune is required. Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Cold Air Intake MAF Kit to suit VF V8 6.0 & 6.2L Engines   >>> The VF Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake MAF Kit to suit VF V8 6.0 & 6.2L Engines then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Suits all Holden VE SS and SSV V8 Commodores including the Holden HSV variants fitted with the 6.0 and 6.2 litre LS2 and LS3 engines, L76 – L77 – L98. Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit ***   Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Cold Air Intake MAFLESS Kit to suit VE V8 6.0 & 6.2L Engines - 2007-2013   >>> The VE Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake MAFLESS Kit to suit VE V8 6.0 & 6.2L Engines - 2007-2013 then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Suits all Holden VE SS and SSV V8 Commodores including the Holden HSV variants fitted with the 6.0 and 6.2 litre LS2 and LS3 engines, L76 – L77 – L98. Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit ***   Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Cold Air Intake MAFLESS Kit to suit VF V8 6.0 & 6.2L Engines >>> The VF Holden owner’s most popular choice when it comes to Over The Radiator Cold Air Intakes <<<   If you're looking for a Cold Air Intake MAFLESS Kit to suit VF V8 6.0 & 6.2L Engines then this is the one for you. More POWER, Increased PERFORMANCE & Better ECONOMY is what is achieved by installing one of these V6 Orssom Performance Cold Air Intakes. Suits all Holden VE SS and SSV V8 Commodores including the Holden HSV variants fitted with the 6.0 and 6.2 litre LS2 and LS3 engines, L76 – L77 – L98. Here's what you get in this Cold Air Intake Kit: Top Intake Cover Lower Filter Housing K&N Air Filter re-washable ( Part No 33-2640 ) 1 Airflow Meter Seal 1 x Rubber Bellow 1 x Hose Clamp 3 x Speed Clips 3 x Phillips Head Screws 1 x 10mm Length Vacuum Breather Hose 1 x Right Angle Breather Pipe ( Optional use on some models Only ) Fitting Instructions And the great thing about these Cold Air Intakes are: NO laying back of radiator to fit the intake NO cutting or lengthening of any electrical wires NO cutting of any body panels to fit intake NO removing bumper bars to clean or replace air filters MAF fitment, (Must be fitted with the factory Air Flow Meter) Can be installed in about 30 minutes 12 months Manufacturers Replacement Warranty from purchase date, against faulty manufacturing (Failure to follow fitting instructions procedure will void warranty). You and your pride and joy are going to love the: Cooler air intake temperatures Increased air flow to your engine Increase in power and torque Excellent throttle response Improvement to your fuel economy Awesome induction sound OEM style for that stealth under bonnet appearance   *** This kit does not include the Airflow Sensor, you MUST use your original factory unit ***   Disclaimer: Orssom Performance Products are designed for off road use only. CAI Pty LTD & Conrod Motorsport Pty Ltd T/A Orssom Performance, accept no responsibility nor will be held liable for any damages caused to Vehicle engines / Vehicles / Property / Lose of life / Injury or Injury to others, as a result of fitment of these products. Please consider carefully if this product is for you before purchasing.   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Door Moulds for VL Holden Commodore Sedan - Calais Style   If you're looking for Door Moulds for VL Holden Commodore Sedan in Calais Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Door Moulds for VL Holden Commodore Sedan - Calais Style Give your VL that sleek, smooth look on the doors with these Calais Style door panels! Great for making the side of a standard Executive VL Commodore look like the VL Calais 100% Australian made Supplied as 6x pieces: 2x panels for both left & right front doors, 2x panels for left & right rear doors & 2x panels for front guard (All pieces also available separately - Contact us for this) These door moulds fill the gap between the side skirts and the upper standard door strips Can be stuck on to door panels with urethane This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Door Moulds for VL Holden Commodore Sedan - LE Style   If you're looking for Door Moulds for VL Holden Commodore Sedan in LE Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Door Moulds for VL Holden Commodore Sedan - LE Style Give your VL that sleek, smooth look on the doors with these LE Style door panels! 100% Australian made Supplied as a set of 4: 2x panels for left & right front doors & 2x panels for left & right rear doors (Also available separately - Contact us for this) These door moulds fill the 'gap' between the side skirts and the upper standard door strips (The front door moulds only are actually the same as the VL Calais moulds) Can be stuck on to door panels with urethane Does not include front guard quarter panel pieces as these parts are part of the LE style side skirts We recommend pairing these door moulds with the LE Style side skirts (See other listing for these), as the side skirts flare out slightly at the rear to match the door moulds This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Door Moulds for VL Holden Commodore - Walkinshaw Style (Set of 4)   If you're looking for Door Moulds for VL Holden Commodore in Walkinshaw Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Door Moulds for VL Holden Commodore - Walkinshaw Style (Set of 4) Give your Commodore a whole new look with these tough looking door moulds! Comes as a set of 4 - 1x panel per door (Can also be bought separately - Contact us for this) New mouldings as per genuine parts 100% Australian made Does not include front guard panels (Are available separately - See other listing) This product is made to order - Please see above for approx build time Quality fibreglass construction  Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Door Moulds for VN / VG / VP / VR / VS Holden Commodore Ute - Aero Style If you're looking for 100% Australian made Door Moulds for VN / VG / VP / VR / VS Holden Commodore Ute in Aero Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Door Moulds for VN / VG / VP / VR / VS Holden Commodore Ute - Aero Style Give your Commodore a whole new look with these tough looking door moulds! Supplied as set of 4 (Also available separately) NOTE: These door moulds are meant to be used with the Aero style side skirts because of how they fit together Meant to be attached to car with urethane 100% Australian made This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Door Moulds for VN / VP / VR / VS Holden Commodore Sedan - Aero Style   If you're looking for 100% Australian made Door Moulds for VN / VP / VR / VS Holden Commodore Sedan in Aero Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Door Moulds for VN / VP / VR / VS Holden Commodore Sedan - Aero Style Give your Commodore a whole new look with these tough looking door moulds! Supplied as set of 4 (Also available separately) NOTE: These door moulds are meant to be used with the Aero style side skirts because of how they fit together (You do not have to have the Aero style side skirts to fit these panels, however it won't 'look' as good if you don't as they won't sit flush to each other) 100% Australian made Meant to be stuck onto door panels using urethane This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

DRIVER Side Quarter Window Panel Surround for VG / VP / VR / VS Holden Commodore Ute   If you're looking for an Australian made DRIVER Side Quarter Window Panel Surround for VG / VP / VR / VS Holden Commodore Ute then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   DRIVER Side Quarter Window Panel Surround for VG / VP / VR / VS Holden Commodore Ute If you've broken your quarter window panel then this is the part for you DRIVER side quarter panel surround (Passenger side also available - see other listing) Australian made Can be attached with urethane & small screws  This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Add to Cart Now  

DRIVER Side Ute Tub Corner End Cap for VG / VP / VR / VS Holden Commodore Ute   If you're looking for an Australian made DRIVER Side Ute Tub Corner End Cap for VG / VP / VR / VS Holden Commodore Ute then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   DRIVER Side Ute Tub Corner End Cap for VG / VP / VR / VS Holden Commodore Ute If you've broken your ute tub corner end cap then this is the part for you DRIVER side rear ute tub corner end cap (Passenger side also available - see other listing) Australian made Mounting holes marked on part (but not drilled) This product is made to order - Please see above for approx build time Custom designed to suit this model Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Add to Cart Now  

DRL Head Lights for VE Holden Commodore Series 1 - Black   If you're looking for a set of DRL Head Lights for VE Holden Commodore Series 1 in Black then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style.   DRL Head Lights for VE Holden Commodore Series 1 - Black Give your Commodore front end a whole new look with these awesome new eye catching head lights! Top quality plastic aftermarket head lights Clear outer lens and black background + daytime running lights which is a row of separate LED's (Row of LED's is for parking lights) These headlights have low beam projector lamps which produce a longer, wider beam that is more focused then conventional headlights and high beam chrome reflector Suits VE Series 1 Omega / SV6 / SS / SS-V 2006 - 08/2010 models Supplied as a pair (Left & Right) Plug & Play - No wiring modification needed – Plugs straight into factory wiring NOTE: To change the head lights on the VE, you may need to remove your bumper first Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, Specials, New Parts and all the latest in the Automotive World!

DRL Head Lights for VE Holden Commodore Series 1 with LED Strip - Black (2006 - 2010 Models)   If you're looking for a set of DRL Head Lights for VE Holden Commodore Series 1 with LED Strip in Black then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style.   DRL Head Lights for VE Holden Commodore Series 1 with LED Strip - Black (2006 - 2010 Models) Give your Commodore front end a whole new look with these awesome new eye catching head lights! Top quality aftermarket head lights Clear outer lens and black background + daytime running lights which is a continuous row of LED's (Instead of separated LED's) (Strip of LED's is powered by parking lights) These headlights have low beam projector lamps which produce a longer, wider beam that is more focused then conventional headlights and high beam chrome reflector Suits VE Series 1 model HSV, SSV, SV & Lumina, Omega, SS, SV6, Berlina & Calais Models (08/2006-08/2010) (Utes 08/2007-08/2010) (Will not suit any Series 2 models) ALSO Suits: HSV Clubsport, GTS & Senator (08/2006-08/2010) & Maloo Models (10/2007-08/2020) Supplied as a pair (Left & Right) Not compatible with AFS function Plug & Play - No wiring modification needed – Plugs straight into factory wiring Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, Specials, New Parts and all the latest in the Automotive World!

DRL LED Head Lights for VE Holden Commodore Series 1 & 2 with Sequential Indicators - Black If you're looking for a set of DRL LED Head Lights for VE Holden Commodore with Sequential Indicators then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style! DRL LED Head Lights for VE Holden Commodore Series 1 & 2 with Sequential Indicators - Black Give your Commodore front end a whole new look with these awesome new eye catching head lights! Top quality aftermarket head lights Clear outer lens and black inner background + daytime running lights (DRL) which is a continuous row of LED's (Instead of separated LED's) Features awesome sequential indicators that blink from one side to the other Suits VE Series 1 & 2 model Commodores (Omega, Berlina etc) - Will NOT fit Caprice or Calais models (A Chrome style strip is provided with lights for if you have a Series 1 model, to cover the gap between the lights and the bumper bar) Supplied as a pair only (Left & Right) Xenon globes included Plugs into factory wiring however some wiring modification may need to be done depending on your car's existing wiring - We highly recommend getting an auto electrician to install them Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!  

DRL LED Head Lights for VE Holden Commodore Series 1 & 2 with Sequential Indicators - Chrome If you're looking for a set of DRL LED Head Lights for VE Holden Commodore with Sequential Indicators then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style! DRL LED Head Lights for VE Holden Commodore Series 1 & 2 with Sequential Indicators - Chrome Give your Commodore front end a whole new look with these awesome new eye catching head lights! Top quality aftermarket head lights Clear outer lens and chrome/black inner background + daytime running lights (DRL) which is a continuous row of LED's (Instead of separated LED's) Features awesome sequential indicators that blink from one side to the other Suits VE Series 1 & 2 model Commodores (Omega, Berlina etc) - Will NOT fit Caprice or Calais models (A Chrome style strip is provided with lights for if you have a Series 1 model, to cover the gap between the lights and the bumper bar) Supplied as a pair only (Left & Right) Xenon globes included Plugs into factory wiring however some wiring modification may need to be done depending on your car's existing wiring - We highly recommend getting an auto electrician to install them Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!  

DRL LED Projector Head Lights for VY Holden Commodore - Black (2002 - 2004 Models)   If you're looking for a set of DRL LED Projector Head Lights for VY Holden Commodore then this is the one for you. Great design and super high quality. Give your car that aftermarket look and style.   DRL LED Projector Head Lights for VY Holden Commodore - Black (2002 - 2004 Models) Give your Commodore front end a whole new look with these awesome eye catching head lights! Top quality aftermarket head lights Suits Sedan, Ute & Wagon 2002-2004 VY Commodore Executive / S Pack / SS / SV8 / Lumina / Equipe models (Does not fit VY Berlina / Calais / HSV models) Supplied as a pair (Left & Right) LED Daytime Running Lights & halogen indicators (halogen globes included for low & high beam) Not compatible with AFS function Plug & Play - No wiring modification needed – Plugs straight into factory wiring Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Tough look plus increases your cars value Very Limited Stock - Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, Specials, New Parts and all the latest in the Automotive World!

Engine Cover for VN / VP / VR / VS / VT V8 Holden Commodore   *** This Engine Cover fits all V8 5 Litre Engines on VN / VP / VR / VS / VT Holden Commodores (Series 1 ONLY for VT) ***   If you're looking for a 100% Australian made Engine Cover for VN / VP / VR / VS / VT V8 Holden Commodore then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Engine Cover for VN / VP / VR / VS / VT V8 Holden Commodore Suits all VN / VP / VR / VS / VT (Series 1 ONLY for VT) V8 5 litre engines Heat resistant  100% Australian made This product is made to order - Please see above for approx build time Quality fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world!

Flares for Holden Colorado Ute - Black - Set of 4 (2016 - 2020 Models)   If you're looking for Flares for Holden Colorado then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Flares for Holden Colorado Ute - Black - Set of 4 (2016 - 2020 Models) Pump out the guards of your Colorado with these awesome aftermarket wheel arch flares! Supplied as a set of 4 for the front & rear wheels Matt Black in colour Low to medium profile flares Super strong ABS plastic construction Flares stick out approx 45mm from vehicle Height of flares approx 6 inches Includes screws & tape Uses existing guard liner bolts - Bolts on under guards out of sight (To mount, screw in under the guard where guard liner is - NO drilling is required. No instructions are included) Please allow 2-3 days for handling BEFORE this item is shipped to you Custom designed to suit this model Quality guaranteed Super strong build quality Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with Sales, New parts and all the goss in the bodykits world! Important note: Prior to fitting this product, ensure your vehicle is thoroughly washed and clean ensuring the mating surface you are fitting the product to is free from any GREASE / WAX / POLISH or any other contaminants. As surface preparation is very important, we recommend the use of a “Wash and Grease Remover” solution to be used on the mating surface as per directions on the solvent bottle you use. Failing to prepare the surface correctly, you risk the possibility of the product not adhering to the surface correctly & coming off. When fitting, apply firm but not excessive pressure or weight. Failing to follow these instructions will void your warranty on the product.

Flares for Holden Torana LH LX Coupe/Hatch - A9X Style If you're looking for Flares for Holden Torana LH LX Coupe/Hatch in A9X Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Flares for Holden Torana LH LX Coupe/Hatch - A9X Style Give your Torana a whole new look with these tough looking wheel arch flares! 100% Australian made Supplied as a set of 4 (Also available as a pair or separately - Contact us for this) A9X style flares are larger on the rear flares and slightly different than the SLR5000 style flares (Rear flares stick out approx 90mm (each side) from body, if measured at 90 degree angle to ground) Can be supplied with fitting kit - Please choose which option above when purchasing (Fitting kit includes rubber piping and stainless steel bolts & nuts) This product is made to order - Please see above for approx build time Custom designed to suit this model Full fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Flares for Holden Torana LH LX Sedan - A9X Style If you're looking for Flares for Holden Torana LH LX Sedan in A9X Style then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.    Flares for Holden Torana LH LX Sedan - A9X Style Give your Torana a whole new look with these tough looking wheel arch flares! Supplied as a set of 4 (Also available as a pair or separately - Contact us for this) 100% Australian made A9X style flares are larger on the rear flares and slightly different than the SLR5000 style flares (Rear flares stick out approx 90mm (each side) from body, if measured at 90 degree angle to ground) Can be supplied with fitting kit - Please choose which option above when purchasing (Fitting kit includes rubber piping and stainless steel bolts & nuts) This product is made to order - Please see above for approx build time Custom designed to suit this model Quality guaranteed Full fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!

Flares for Holden Torana LH LX SLR 5000 Sedan - SLR 5000 Style If you're looking for Flares for Holden Torana LH LX SLR 5000 Sedan then this is the one for you. Tough look, plus tough construction. Give your car that aftermarket look and style.   Flares for Holden Torana LH LX SLR 5000 Sedan - SLR 5000 Style Give your Torana a whole new look with these tough looking wheel arch flares! Supplied as a set of 4 (Also available as a pair or separately - Contact us for this) Can be supplied with fitting kit - Please choose which option above when purchasing (Fitting kit includes rubber piping and stainless steel bolts & nuts) 100% Australian made This product is made to order - Please see above for approx build time Custom designed to suit this model Full fibreglass construction Super strong build quality Make sure to pre-fit this item before prepping/modifying/painting it Comes unpainted - Gel coat finish - Ready to prep & paint (Gel coat colour may be black, grey or white depending on materials at time of construction) This is a 100% hand made fibreglass item so please note that some adjustment, sanding, trimming etc may be applicable in preparing & fitting this item, especially when fitting to older vehicles or vehicles that have previously been in an accident Tough look plus increases your cars value Scroll up and Add to Cart NOW!   Follow us on Facebook HERE to stay up to date with sales, new parts and all the goss in the bodykits world!